Fabric Painting And Dyeing

Fabric Painting And Dyeing @ Amazon.com

I’ve run all over this a lot in my travels, a client asks “Can you dye my cloth seats?” My answer to them is, “No, I can’t in truth dye your seats. What I may do is paint your seats.”

Dyeing and painting cloth are two very dissimilar things.

Dyeing cloth comprises of immersing the entire fabric in a dye solution, soaking it through and through for a amount of time of time, then rinsing the excess dye away. Rinsing removes any excess dye left so not to transfer onto something that you don’t want dyed like your clothes. Dyeing cloth is a more permanent way to modify a color. The dyes genuinely penetrate the fibers of the fabric.

Painting cloth comprises of spraying a solution of colored pigments and a binder of a great deal of sort onto the cloth. This procedure is commonly employed to rejuvenate an existent color or somewhat modify a color. When attempting to change a color you normally will have to go darker not lighter. If you have a dark gray and want to go light gray, won’t work. Painting cloth may be tricky, but may yield a lot of genuinely nice jobs. Painting cloth may be a semi-permanent way to alter the color of fabric. Usually the paint will finally wear off on high traffic areas. The paint lays on top of the fibers. Designs may likewise be done by the paint method, normally with an airbrush.

So with that said painting cloth seats may be done. Dyeing a cloth seats, well…. if your more than willing to tear your seats detached and hope the fabric doesn’t shrink while washing it in the dye solution, which most fabric dyes require hot water, then dyeing a cloth seat may be done too, but with a lot of work. I guess it could save a little on reupholstering, but with all that venture you might as well go in front and go all the way and just add new fabric the color you want. But to each his own, I guess if you have a new car and want it dissimilar color then maybe, that’s new fabric.

I got into a occupation today that you almost had to laugh at. This was a lot of time and crusade put into a vehicle that if finished in all likelihood could have been a show car if…and I mean if….it were a dissimilar car. It was a 2006 Suzuki Forenza, that someone had put habit crushed velvet silver with emerald green inserts. Tucked, quilted, molded and sewn just right. The occupation was done in truth well, just didn’t genuinely match anything. The car was white with a two tone gray interior. They had done all four seats, headliner, door panels and trunk area only.Kinda looked like somebody just wasn’t rather done. I don’t know it didn’t match and necessitated to get sold.

So my occupation was to turn the green to black.

Doing this took a great deal of prep time, I thought of just going in with a blocking card and paint and going to town but then I thought again, too a good deal of curves and just too much area. Masking was my only way. Now masking cloth may be a pain, commonly tape just genuinely doesn’t stick that well and I was a little worried, but this material kept tape very well, thank God. Not actually sure what it was, surely a good deal of sort of synthetic. If ever you run into a problem with your tape not sticking to cloth, I’ve found if you heat the tape a little with a hair dryer while applying it, it will stick better. The tape from 3M and from Scotch Tape, work the best I think. Anyways I taped off the entire areas using a 1.5″ tape. This took with regards to an hour, paying close attention not to tape over the green or exposing any of the silver. I applied my blocking card for the rest. Papering it off too is just a waste to me, I may use a blocking card most of the time and tape and get the same effect. Less material cost….

Now mixing up your paint solution. I used my water based vinyl paints to do this. Vinyl paints are dye pigments mixed with resins, or your binder. Water based works best for cloth, solvents seem to leave the cloth stiff and hard looking where water based paints are more flexible leaving the cloth sentiment and looking more natural. And I see your questions flying, “Water Based?” “Will it wash off on my clothes?” Water based means the pigments and resins are water soluble, fundamentally meaning when the water evaporates the paint is permanent. It won’t come off on your costume once done, if done correctly.

I mixed my paint with when it comes to 2 oz. paint to 1 oz. water, with a dab of slip additive for a softer feel, and rubbing alcohol to aid evaporate the water rapidly and without delay boosting arid time. I watered it down to help it absorb into the fabric better. Doing it this way helps to give you that softer feel in the end, more time, but worth the effort.

I laid around two coats on each panel before moving onto the next, then went back after wards and laid another coat to deepen the black. The darker designs on the fabric showed through giving it a gorgeous cool effect. It worked out genuinely well.

I did this occupation today and will in all likelihood have to go back tomorrow to touch it up and brush the fabric, this will remove any excess left over and give the cloth a softer feel. Touching it up will consist of either having to dye the seats again or just laying a light coat over them. Sometimes the dye will soak into the fabric and lighten as it dries basically the other color will bleed back through. You in truth can’t tell if your genuinely done until they are completely dry. So there’s where the time thing come in.

Painting your cloth seats may give you a revive to your ride or give you a new look all together. Just do not forget when doing so to use a water based paint to give you the feel and look your looking for.